IPHONE
09-29-2008, 11:42 AM
Simple CW600s ugrade new OS intstructions
1- A CW600s receiver
2- Null Modem Cable
3- New OSD software bin files “CX_KroundV1.06.bin and CX-LoaderV2.50.bin” for CW600s model FTA receiver
4- Loading Software CW600 v1.04 and also New CW600 V1.05
All file are available for download in file section.
1) Connect your PC and receiver with twisted RS-232C Null modem cable.
2) Power off the receiver from the back switch.
3) You must load this new OSD in “boot” mode. Here how you get into “boot”mode
Hold power button on the front of the receiver and turn the power ON from the back of the receiver.
You will see a word “boot” on the front LCD screen of the receiver.
4) If you have USB to serial cable and a Virgin brand new receiver then you have to first load
new OSD bin file using a null modem cable or load old OSD V142 or latest bin file to make your
USB to serial cable work.
5) Run the LoaderV1.04 on your PC. Select the right COM port where you connected your null modem cable
usually COM1, then select , press and select the bin file,CX_KroundV1.06_24138Chip.bin then click ,
upgrade will begin.
6) After finishing, the receiver LED will display "-End"
If your experience any problem during the upgrade start over again.
7) Turn receiver Off from the back and then ON the receiver; you will see 00:00 now press "POWER" key
on front of the receiver panel to make it standby, the LED dot will display “- - : - -“.
8) Start New LoaderV1.05 check if the right COM port is selected then select
, press and select the bin file,CX-LoaderV2.50 then click , upgrade will begin
If you will not upload the CX-LoaderV2.50.bin you will not be able to Enable the Patch to watch
scrambled channels. While loading the software make sure Power is always ON and do not touch any buttons
while loading these new bins. It may damage you receiver.
From now on you have to use Loader V1.05 to upgrade your receiver for new updates. Since you have loaded
the new OSD bin to your receiver now you can not roll back to older OSD anymore. Do not try to load
old OSD bin to your receiver it may damage your receiver. DO NOT load this file into any other receiver
other than Captiveworks CW-600S receiver because it may damage your receiver.
Now you have successfully loaded the latest software to your receiver. It is now ready to scan
satellites channels and have fun with it.
1- A CW600s receiver
2- Null Modem Cable
3- New OSD software bin files “CX_KroundV1.06.bin and CX-LoaderV2.50.bin” for CW600s model FTA receiver
4- Loading Software CW600 v1.04 and also New CW600 V1.05
All file are available for download in file section.
1) Connect your PC and receiver with twisted RS-232C Null modem cable.
2) Power off the receiver from the back switch.
3) You must load this new OSD in “boot” mode. Here how you get into “boot”mode
Hold power button on the front of the receiver and turn the power ON from the back of the receiver.
You will see a word “boot” on the front LCD screen of the receiver.
4) If you have USB to serial cable and a Virgin brand new receiver then you have to first load
new OSD bin file using a null modem cable or load old OSD V142 or latest bin file to make your
USB to serial cable work.
5) Run the LoaderV1.04 on your PC. Select the right COM port where you connected your null modem cable
usually COM1, then select , press and select the bin file,CX_KroundV1.06_24138Chip.bin then click ,
upgrade will begin.
6) After finishing, the receiver LED will display "-End"
If your experience any problem during the upgrade start over again.
7) Turn receiver Off from the back and then ON the receiver; you will see 00:00 now press "POWER" key
on front of the receiver panel to make it standby, the LED dot will display “- - : - -“.
8) Start New LoaderV1.05 check if the right COM port is selected then select
, press and select the bin file,CX-LoaderV2.50 then click , upgrade will begin
If you will not upload the CX-LoaderV2.50.bin you will not be able to Enable the Patch to watch
scrambled channels. While loading the software make sure Power is always ON and do not touch any buttons
while loading these new bins. It may damage you receiver.
From now on you have to use Loader V1.05 to upgrade your receiver for new updates. Since you have loaded
the new OSD bin to your receiver now you can not roll back to older OSD anymore. Do not try to load
old OSD bin to your receiver it may damage your receiver. DO NOT load this file into any other receiver
other than Captiveworks CW-600S receiver because it may damage your receiver.
Now you have successfully loaded the latest software to your receiver. It is now ready to scan
satellites channels and have fun with it.