IPHONE
09-29-2008, 12:15 PM
Loading the 8100 with Loader and Cable
How to update with current bin using cs upgrade loader V3.01
before you begin…
1) each of the required files below must be unzipped
2) the unzipped files should be saved to a folder
3) You must Factory Reset the receiver before you begin and you should have all your antenna settings written down
4) Turn the receiver off from the back power switch after the factory reset.
5) Connect the null (RS232) cable to your PC and the Receiver
6) Disconnect Satellite cable, if necessary
Open the loader; New loader CSUpgrade_v3.01.exe
NOTE: Depending on your operating system (Windows 98, 2000, XP and
Vista) you may need following three ocx files in the same directory
where CSUpgrade_v3.01 is located and also under C:\Windows\System32.
1) comctl32.ocx
2) comdlg32.ocx
3) mscomm32.ocx
How to apply the ocx file: Copy and paste the following command into
command window (by typing ‘cmd’ on run) Copy the command line below
(one line at a time) and paste in command window by clicking the “right
mouse button” and press enter
regsvr32 C:\windows\system32\comctl32.ocx
regsvr32 C:\windows\system32\comdlg32.ocx
regsvr32 C:\windows\system32\mscomm32.ocx
first step loading the clear_SW_HD.Bin file…
Bin Files Coolsat 8100 hd file Fix Software Help
Once the loader is up and running, do not change any selection, simply
click on “Browse” to locate and select the unzipped file
Clear_SW_HD.bin. Upon selection you will see the file in the window,
click "Start" and also turn the receiver ON from the back and wait for
the file to download and complete. This will take 3-5 minutes. Once
completed, turn the receiver off from the back and click OK on the
completed pop-up.
second step loading the factory flash…
Using the same loader program, do not change any selection, simply
click on “Browse” to locate and select the unzipped file original
Factory Flash -11170A.sgn. Upon selection you will see the file in the
window, click "Start" and also turn the receiver ON from the back and
wait for the file to download and complete. This will take 3-5 minutes.
Once completed, turn the receiver off from the back and click OK on the
completed pop-up. Factory reset again.
last step loading the latest bin…
Using the same loader program, do not change any selection, simply
click on “Browse” to locate and select the unzipped copy of current
file ending in .sgn. Upon selection you will see the file in the
window, click "Start" and also turn the receiver ON from the back and
wait for the file to download and complete. This will take 3-5 minutes.
Once completed, turn the receiver off from the back and click OK on the
completed pop-up
before you end…
1) Unplug the null cable from the back of the receiver and PC
2) Hook the receiver back up to the satellite cable.
3) Power up the receiver from the back
4) Let it auto-scan or scan as per your setup
5) Make sure that the auto-roll is ON and your settings are correct.
6) wait for the receiver to perform auto roll
How to update with current bin using cs upgrade loader V3.01
before you begin…
1) each of the required files below must be unzipped
2) the unzipped files should be saved to a folder
3) You must Factory Reset the receiver before you begin and you should have all your antenna settings written down
4) Turn the receiver off from the back power switch after the factory reset.
5) Connect the null (RS232) cable to your PC and the Receiver
6) Disconnect Satellite cable, if necessary
Open the loader; New loader CSUpgrade_v3.01.exe
NOTE: Depending on your operating system (Windows 98, 2000, XP and
Vista) you may need following three ocx files in the same directory
where CSUpgrade_v3.01 is located and also under C:\Windows\System32.
1) comctl32.ocx
2) comdlg32.ocx
3) mscomm32.ocx
How to apply the ocx file: Copy and paste the following command into
command window (by typing ‘cmd’ on run) Copy the command line below
(one line at a time) and paste in command window by clicking the “right
mouse button” and press enter
regsvr32 C:\windows\system32\comctl32.ocx
regsvr32 C:\windows\system32\comdlg32.ocx
regsvr32 C:\windows\system32\mscomm32.ocx
first step loading the clear_SW_HD.Bin file…
Bin Files Coolsat 8100 hd file Fix Software Help
Once the loader is up and running, do not change any selection, simply
click on “Browse” to locate and select the unzipped file
Clear_SW_HD.bin. Upon selection you will see the file in the window,
click "Start" and also turn the receiver ON from the back and wait for
the file to download and complete. This will take 3-5 minutes. Once
completed, turn the receiver off from the back and click OK on the
completed pop-up.
second step loading the factory flash…
Using the same loader program, do not change any selection, simply
click on “Browse” to locate and select the unzipped file original
Factory Flash -11170A.sgn. Upon selection you will see the file in the
window, click "Start" and also turn the receiver ON from the back and
wait for the file to download and complete. This will take 3-5 minutes.
Once completed, turn the receiver off from the back and click OK on the
completed pop-up. Factory reset again.
last step loading the latest bin…
Using the same loader program, do not change any selection, simply
click on “Browse” to locate and select the unzipped copy of current
file ending in .sgn. Upon selection you will see the file in the
window, click "Start" and also turn the receiver ON from the back and
wait for the file to download and complete. This will take 3-5 minutes.
Once completed, turn the receiver off from the back and click OK on the
completed pop-up
before you end…
1) Unplug the null cable from the back of the receiver and PC
2) Hook the receiver back up to the satellite cable.
3) Power up the receiver from the back
4) Let it auto-scan or scan as per your setup
5) Make sure that the auto-roll is ON and your settings are correct.
6) wait for the receiver to perform auto roll